Career and Education Opportunities for Numerical Control Tool Programmers in Eugene, Oregon
Numerical control tool programmers can find many career and educational opportunities in the Eugene, Oregon area. About 330 people are currently employed as numerical control tool programmers in Oregon. By 2016, this is expected to grow 6% to 360 people employed. This is better than the national trend for numerical control tool programmers, which sees this job pool shrinking by about 15.4% over the next eight years. In general, numerical control tool programmers develop programs to control machining or processing of parts by automatic machine tools, equipment, or systems.
Numerical control tool programmers earn approximately $25 per hour or $53,350 per year on average in Oregon. Nationally they average about $21 per hour or $44,310 annually. Earnings for numerical control tool programmers are better than earnings in the general category of Computer Controls in Oregon and better than general Computer Controls category earnings nationally.
The Eugene area is home to seven schools of higher education, including two within twenty-five miles of Eugene where you can get a degree as a numerical control tool programmer. Numerical control tool programmers usually hold an Associate's, or other 2-year degree, so you can expect to spend about two years studying to be a numerical control tool programmer if you already have a high school diploma.
CAREER DESCRIPTION: Numerical Control Tool Programmer
In general, numerical control tool programmers develop programs to control machining or processing of parts by automatic machine tools, equipment, or systems.
Numerical control tool programmers analyze job orders, drawings, blueprints, specifications, printed circuit board pattern films, and layout data so as to calculate dimensions and feed rates. They also decide on the sequence of machine operations, and decide on the proper cutting tools needed to machine workpieces into the desired shapes. Equally important, numerical control tool programmers have to modify existing programs to enhance efficiency. They are often called upon to decide on reference points, machine cutting paths, or hole locations, and compute angular and linear dimensions, radii, and curvatures. They are expected to observe machines on trial runs or conduct computer simulations to insure that programs and machinery will function properly and produce items that meet specifications. Finally, numerical control tool programmers revise programs and/or tapes to remove errors, and retest programs to check that problems have been solved.
Every day, numerical control tool programmers are expected to be able to visualize how things come together and can be organized. They need to see details at a very fine level of focus. It is also important that they imediately see the relationships between collections of numbers, images, and patterns.
It is important for numerical control tool programmers to enter computer commands to store or retrieve components patterns or programs that transfer data to other media. They are often called upon to ready geometric layouts from graphic displays, using computer-assisted drafting software or drafting instruments and graph paper. They also compare encoded tapes or computer printouts with original part specifications and blueprints to confirm precision of instructions. They are sometimes expected to enter coordinates of hole locations into program memories by depressing pedals or buttons of programmers. Somewhat less frequently, numerical control tool programmers are also expected to write instruction sheets and cutter lists for a machine's controller so as to guide setup and encode numerical control tapes.
Numerical control tool programmers sometimes are asked to draw machine tool paths on pattern film, using colored markers and following guidelines for tool speed and efficiency. and revise programs and/or tapes to remove errors, and retest programs to check that problems have been solved. And finally, they sometimes have to observe machines on trial runs or conduct computer simulations to insure that programs and machinery will function properly and produce items that meet specifications.
Like many other jobs, numerical control tool programmers must be thorough and dependable and be able to absorb the factors involved and a problem and provide a well thought out solution.
EDUCATIONAL OPPORTUNITIES: Numerical Control Tool Programmer Training
Northwest Christian University - Eugene, OR
Northwest Christian University, 828 East 11th Avenue, Eugene, OR 97401-3745. Northwest Christian University is a small university located in Eugene, Oregon. It is a private not-for-profit school with primarily 4-year or above programs. It has 534 students and an admission rate of 54%. Northwest Christian University has a bachelor's degree program in Computer Programming/Programmer.
Lane Community College - Eugene, OR
Lane Community College, 4000 E 30th Ave, Eugene, OR 97405-0640. Lane Community College is a large college located in Eugene, Oregon. It is a public school with primarily 2-year programs and has 9,290 students. Lane Community College has a less than one year and an associate's degree program in Computer Programming/Programmer which graduated six and two students respectively in 2008.
LOCATION INFORMATION: Eugene, Oregon
Eugene is located in Lane County, Oregon. It has a population of over 150,104, which has grown by 8.9% over the last ten years. The cost of living index in Eugene, 98, is near the national average. New single-family homes in Eugene cost $197,200 on average, which is below the state average. In 2008, one hundred eighty-one new homes were constructed in Eugene, down from two hundred ninety-seven the previous year.
The three most popular industries for women in Eugene are educational services, health care, and accommodation and food services. For men, it is educational services, construction, and professional, scientific, and technical services. The average commute to work is about 17 minutes. More than 37.3% of Eugene residents have a bachelor's degree, which is higher than the state average. The percentage of residents with a graduate degree, 15.4%, is higher than the state average.
The unemployment rate in Eugene is 9.9%, which is less than Oregon's average of 10.6%.
The percentage of Eugene residents that are affiliated with a religious congregation, 24.5%, is less than both the national and state average. The most common religious groups are the Catholic Church, the LDS (Mormon) Church and the International Church of the Foursquare Gospel.
Eugene is home to the Eugene Country Club and the Balboa Park Drag Strip as well as Acorn City Park and Monroe City Park. Visitors to Eugene can choose from Hawthorn Inn & Suites, Best Value Inn and Marriott Residence Inn for temporary stays in the area.